T. E. Bilderback and M. A. Powell
Extension Horticulture Specialists
Publication Number: AG-508-6
Last Electronic Revision: March 1996 (JWM)
Just as we zone plants in the landscape according to their different water needs, irrigation systems should be zoned so that plants with different water needs are irrigated separately. Turfgrass, for example, should be watered separately from shrubs and flowers.
Using irrigation water efficiently also requires proper selection of irrigation methods for the plants and for each area of the landscape.
Trees and shrubs in the low-water-use zone need supplemental water only during establishment or the first growing season (first 8 to 10 weeks after transplanting), whereas plants in moderate-water-use zones require water only during periods of limited rainfall when they show signs of stress. For these plants, a temporary system such as a soaker hose or hand watering may be all that is required. On the other hand, high-water-use zones require frequent water- ing and may warrant a permanent system with automatic controls. Whenever possible, use highly efficient watering techniques, such as drip irrigation.
This publication describes several types of irrigation systems and presents irrigation guidelines that should help you make wise-water-use landscaping decisions.
Many types of sprinklers are available for use in the landscape. Permanent systems with pop-up spray heads are most common. They are installed underground and rise above the ground surface to operate. Some are designed for use in turf (those having 2- to 3- inch pop-up height); others are designed for use in beds of taller plants (with a 6- to 12-inch pop-up height). Some sprinkler heads are designed for watering small, irregularly shaped areas. These typically have a radius of 15 feet or less. Others, like rotary sprinkler heads, wet a radius of 20 to 50 feet and are used to irrigate large areas. Most sprinklers are available with either full-circle or part-circle patterns, and most have an adjustable radius for watering irregular areas.
Proper spacing of sprinklers is critical in achieving uniform water application. Sprinklers spaced too far apart will waste water by applying too much water in some areas and not enough in others. On the other hand, spacing sprinklers closer than required increases the cost of the system and wastes water. In general, the spacing between sprinklers should be about 50 to 60 percent of the wetted diameter. For example, sprinklers with a wetted diameter of 80 feet should be spaced 40 to 50 feet apart.
When part-circle sprinklers are used on the same zone with full-circle sprinklers, the sprinklers should be carefully selected to achieve a matched precipitatior rate. A half-circle sprinkler waters only half as much area as a full-circle sprinkler; therefore it should discharge only half as much water. If a full-circle sprinkler discharges 6 gallons per minute, then a half-circle sprinkler should deliver 3 gallons per minute and a quarter-circle sprinkler 1l/2 gallons per minute. Most manufacturers offer sprinklers with matched precipitation rate (MPR) nozzles.
One other important aspect of proper design is pipe sizing. Selection of pipe sizes should be based on the flow rate through the pipe. If pipes are too small, excessive pressure losses occur. This causes some sprinklers to apply more water than others and re- sults in nonuniform application and wasted water. Additional information on pipe sizing and irrigation system design is provided in design manuals avail- able from sprinkler manufacturers.
Rotary sprinklers usually have application rates of 1/4 to l/2 inch per hour and rarely cause runoff. Spray heads, on the other hand, typically have application rates between 1 and 2 inches per hour and may cause runoff on clay soils, especially on slopes greater than l0 percent. If runoff occurs, apply only half the total amount of water, then turn the system off for an hour or two to let the water soak in before applying the remainder of the water. Many irrigation controllers can be programmed to cycle irrigation applications.
The application rate of a sprinkler system can be determined by placing three or four rain gauges at random locations in an irrigated area for a predetermined length of time, usually 1 hour. Figure 1 illustrates gauge placement. By knowing the application rates of your sprinkler system, you can operate the system to apply a given amount of water and avoid wasting water. The average water level within the gauges is a measure of the output of the system in inches per hour (if the test was conducted over a 1-hour period). Repeat this procedure in each sprinkler zone, particularly if different types of sprinklers are used on different zones.
Drip irrigation is recommended for use on trees, shrubs, and flowers in the high- and moderate-water-use zones of the landscape to maximize efficiency. Several types of drip irrigation systems can be adapted to suit a variety of applications, from watering individual trees and shrubs to beds of annuals, herbaceous perennials, ground covers, or mixed borders.
Emitters may be purchased separately from the tubing and placed in the line wherever watering is desired. Another option is to purchase drip tubing with emitters already installed at the factory, usually spaced 12 to 24 inches apart. Most emitters will discharge water at a rate of 1/2, 1, or 2 gallons per hour at a pressure of about 20 pounds per square inch (psi).
Perforated or porous pipe discharges water along its entire length to wet a continuous strip. By spacing pipes 12 to 18 inches apart, it is possible to wet a solid area. It is a good system for closely spaced plantings of annuals, herbaceous perennials, or ground covers.
Most drip systems include polyvinylchloride (PVC) pipe for the main lines and polyethylene (PE) tubing for distribution lines. Polyethylene tubing is flexible, easy to cut, and can be connected without glue or clamps. Emitters are installed by punching a hole in the polyethylene tubing and snapping the emitters into place.
A drip system must have a main valve to turn it on and off. This may be an automatic electric valve connected to a controller or a manual gate valve. You can also connect the drip lines directly to an outside faucet. However, when connecting the system directly to the faucet, use an automated timer to turn the system off after a preset length of time. Otherwise, you may forget and leave the system on for several days.
Two other necessary components of a drip system are a filter and a pressure regulator (Figure 2). A drip system uses small passageways to control the rate of water application so even tiny particles suspended in the water may cause clogging. To prevent clogging, use a screen filter with a 150- to 200-mesh screen. These components are usually installed below ground in a valve box.
Most drip systems are designed to operate at a pressure of about 20 psi. In comparison, household water pressure typically ranges from 40 to 100 psi. A pressure regulator installed immediately after the filter in the main irrigation line reduces the pressure in the line and helps to ensure efficient system operation.
For trees and shrubs, it is generally best to use a system that allows you to insert emitters wherever water is needed. The appropriate number of emitters per plant and flow rate per emitter depend on the size and type of plant. Generally, the larger the plant, the more water it requires. Table 1 lists plant heights and the number of emitters needed to deliver adequate water.
During very dry weather, an emitter system needs to run about three times per week for 4 hours each time to meet the optimum water needs of the plants. Keep in mind that some species require more water than others. Consider this when installing emitters.
For watering annuals, perennials, and ground covers, it is usually necessary to irrigate a solid area. This can be done using emitter lines with emitters spaced every 12 to 18 inches. By placing emitter lines 12 to 18 inches apart, a uniform wetting pattern can be achieved. Perforated or porous pipe spaced every 12 to 18 inches apart can also be used. In sandy soils, the lines will need to be closer together than in finer-textured clay soils. In annual flower beds, the drip lines can be laid aside during bed preparation and replaced afterward.
|Table 1. Emitter Installation Based on Plant Size|
|Plant Height (ft)||Number of Emitters Per Plant||Delivery Rate|
|Less than 2||1||1/2 gal/hr|
|4to6||2||1 gal/hr each|
|6to7||3||1 gal/hr each|
|7to8||4||1 gal/hr each|
|OR:||2||2 gal/hr each|
A similar method of watering uses small sprinkler heads, called microsprinklers, instead of emitters. All other components are identical to drip irrigation, including the polyethylene distribution lines. Microsprinklers spray an area 3 to 12 feet wide and are used for trees and shrubs or beds requiring complete coverage. Microsprinklers may be prone to vandalism and are not quite as efficient as emitters, but they do provide an economical method of achieving uniform watering.
In landscaping, drip irrigation tubing is usually installed on top of the ground and concealed beneath mulch. This makes the system easy to install and service. However, if vandalism is likely, the tubing can also be installed 4 to 6 inches beneath the soil surface with small microtubing (1/8 to 1/4 inch) protruding to the surface. Extend the microtubes 4 to 6 inches above ground to allow for easy inspection and prevent dirt from back-siphoning into the emitters and clogging the system.
When watering by hand, apply about 5 gallons of water per 10 square feet, which is approximately the amount of water delivered by a % -inch garden hose operating for 1 minute at medium pressure. Watering small shrubs (less than 4 feet in height) for 1 minute with the hand-held hose should suffice. Larger shrubs (4 feet and up) will require slightly more water. Increase the watering time by 15 seconds for each foot of height over 4 feet. For large trees apply about 6 to 7 gallons for each 10 square feet of canopy area. For best results, check the output of your faucet by determining the number of seconds it takes to fill a 1-gallon jug and then estimating output per 60 seconds. If runoff occurs before you have applied the correct amount of water, move on to another spot and come back after the water has soaked in.
A rainfall sensor attached to the controller detects rainfall and prevents the irrigation system from operating if significant rainfall has occurred. Another type of sensor measures soil moisture and overrides the system when soil moisture is adequate. Sensors are especially useful if the system cannot be monitored and adjusted regularly.
You can buy many different types of controllers. Make sure you get one with the features you need. When managed properly, an automatic controller can pay for itself in reduced water usage, cost, and labor.
Turf under water stress appears dull bluish green, the leaf blades roll inward, and footprints remain on the grass after a person walks over an area. To pre-vent serious plant damage and maximize water-use efficiency, irrigate turf in the moderate-water-use zones with a portable lawn sprinkler within 24 to 48 hours after these signs appear.
Under optimum growing conditions in a high-water-use zone, turfgrasses use 1 to ll/2 inches of water per week during hot, dry weather. It is usually best to divide this amount into two applications per week, applying l/2 to 3/4 inch each time. Never apply more than 1 inch at a time as this will likely result in runoff or deep percolation below the root zone. Early or late in the season when temperatures are cooler, irrigating only once a week is usually adequate.
Never water grass daily except during the establishment period. Daily irrigation with a small amount of water encourages a shallow root system and reduced drought tolerance, as shown in Figure 4. Since roots generally grow where the soil is moist, a shallow root system also prevents efficient uptake of plant nutrients. Shallow, frequent irrigation also increases evaporative water loss from the soil.
Use drip irrigation on trees and shrubs in the water-use zones of the landscape. Locate the emitters within the drip zone line of plants where the concentration of absorbing roots is the highest. During extended dry periods, operate the system 1 to 2 times per week. Run the system long enough to thoroughly wet the soil 6 to 8 inches deep. Regular and thorough watering of newly planted trees and shrubs encourages good root establishment and greater drought resistance.
Not Shown:Figures 1-4.
|Back up one||Return to WQWM Home Page|